Skip to content

Petroleum knowledge center

Oil & Gas Fundamentals

A practical guide to crude oil characterization, product testing and refinery processing—from the chemistry in a sample to the quality decisions around a barrel.

Crude characterizationProduct quality & testing
Petroleum refinery distillation columns and process piping at sunrise

01 · Crude characterization

Crude oil composition and classification

Crude oil is not one chemical. It is a complex mixture of hydrocarbons with smaller quantities of sulfur, nitrogen, oxygen, metals, water and solids. Its behavior depends on the whole mixture—and on temperature, pressure and handling.

Classification is a useful shorthand, but refinery decisions need measured properties and distillation data. “Light” does not automatically mean low sulfur, and “sweet” does not mean easy to pump.

Paraffins

Straight- and branched-chain saturated hydrocarbons. Light paraffins contribute to volatile fractions; long-chain waxes can raise pour point and complicate cold handling.

Naphthenes

Saturated ring structures, also called cycloparaffins. They occur across many crude fractions and influence density and product properties.

Aromatics

Unsaturated ring structures such as benzene-, toluene- and xylene-related compounds. Their effects depend on concentration, fraction and product rules.

Resins & asphaltenes

Polar, higher-molecular-weight material concentrated in heavy fractions. Asphaltenes are operationally defined by insolubility in a specified alkane; blending can disturb their stability.

The labels people use

Light, medium and heavy
Broad density classes commonly described with API gravity. Higher API gravity means lower density. Boundaries vary by convention, so the number matters more than the label.
Sweet and sour
Lower- and higher-sulfur descriptions. The threshold is convention-dependent; sulfur may also be distributed unevenly among fractions.
API gravity
Calculated from specific gravity at 60 °F: API = 141.5 ÷ specific gravity − 131.5. Density measurements must be corrected to the stated reference temperature.

Properties that change the handling plan

Sulfur concentration

Influences corrosion management, hydrotreating severity, catalyst exposure and finished-product compliance.

Viscosity

Changes strongly with temperature. Pumping assessments need the actual temperature profile, especially for waxy or heavy crude.

Total Acid Number (TAN)

Measures titratable acidic material under test conditions. High-temperature corrosion risk also depends on acid type, flow, metallurgy and operating conditions.

Basic Sediment & Water (BS&W)

A commercial and operational measure of unwanted water and solids. Representative sampling and the chosen test procedure are crucial.

Pour point and wax

Long-chain paraffins can crystallize as temperature falls, increasing restart pressure or restricting flow. Pour point is only one part of the assessment.

Asphaltenes and resins

Heavy, polar material can precipitate when pressure, temperature or blend composition changes, creating fouling and emulsion problems.

Nickel and vanadium

Trace metals concentrate in heavy fractions and can poison or foul conversion catalysts. Other contaminants may also require analysis.

Compatibility

Two stable crudes can form an unstable blend. Compatibility testing examines precipitation risk before storage, transport or processing.

Interactive comparison

Compare three crude profiles

Physical properties & fraction yields

Select two profiles to compare the properties that influence crude handling, processing and product distribution.

Light crude

Lower density and viscosity, with a larger share of lighter fractions.

Heavy crude

Higher density and viscosity, with a larger share of residue.

API gravity

Higher values indicate lower density
A · Light crude38 °API
B · Heavy crude18 °API

Sulfur

Total sulfur by mass
A · Light crude0.2 % by mass
B · Heavy crude2.4 % by mass

Viscosity at 40 °C

Kinematic viscosity at 40 °C
A · Light crude6 mm²/s
B · Heavy crude180 mm²/s

Processing demand

Relative comparison across the three profiles
A · Light crude1 relative 1–3
B · Heavy crude3 relative 1–3

Crude assay distribution

Volume distribution by fraction · each profile totals 100%
Light crudeLower relative conversion demand
28%
16%
24%
18%
14%
Medium crudeModerate relative conversion demand
20%
13%
22%
22%
23%
Heavy crudeHigher relative conversion demand
17%
24%
41%
NaphthaKeroseneDieselGas oilResidue

A complete assay combines representative sampling, measured distillation data and fraction-specific analysis to support refinery planning.

02 · Analytical characterization

Understanding Crude Oil Assays: From Composition to Refinery Value

A crude assay links whole-crude inspection tests with boiling-range separation and analysis of the resulting fractions. It helps a refiner estimate potential yields and identify constraints; it does not guarantee commercial value or refinery performance.

True Boiling Point (TBP) distillation uses a high-separation-efficiency laboratory system to characterize the crude’s boiling distribution. Atmospheric distillation handles lighter material; vacuum distillation extends the analysis into heavier material while limiting thermal degradation. Gas chromatographic simulated distillation may complement, but is not identical to, physical distillation.

01

Separate

Fractions such as naphtha, kerosene, diesel, gas oil and residue are collected across defined boiling intervals. Cut points determine the stream boundaries.

02

Characterize

Each fraction may be tested for sulfur, nitrogen, density, viscosity, metals and other properties. Contaminants are not distributed evenly.

03

Evaluate

Yield and quality data support feedstock comparison, blending studies and refinery models. Compatibility and operating constraints remain part of the decision.

Select a fraction

A simplified distillation column

Lighter fractions rise; heavier fractions remain lower. Select a tray to explore the stream.

Ranges overlap because refinery cut points and crude composition vary. Vacuum gas oil is separated in a downstream vacuum unit.

Upper column

Naphtha

Initial boiling point to roughly 180 °C

General character
A light, volatile mixture. Light and heavy naphtha cuts have different compositions and downstream uses.
Typical applications
Gasoline blending components, catalytic reformer feed and petrochemical feedstock, depending on composition.
Quality considerations
Volatility, sulfur, olefins, aromatics and contaminants influence handling and downstream processing.
Why an assay is not a refinery guarantee

Assay yields reflect the sample, analytical method and chosen cut points. Refinery yields also depend on unit configuration, conversion severity, product specifications, hydrogen availability, utilities, operating limits and economics.

Crude compatibility can change storage and processing behavior. A blend is not simply the average of two assays when phase stability, corrosion or reactions introduce nonlinear effects.

03 · Product quality

Petroleum products and their technical specifications

A product specification converts intended use into measurable requirements. The test method, units, temperature, sampling point and edition all matter. A value without those conditions can be impossible to interpret.

Open a product to see what is measured, why it matters and which test methods and standards are commonly referenced.

01Crude oil

A crude assay combines inspection tests with distillation and fraction analysis. No single property describes refinery value on its own.

Specification context: There is no universal crude-oil specification. The assay, sales agreement, receiving facility and applicable regulation define the required tests and acceptance basis.

Crude oil technical properties and testing considerations
PropertyWhat is measuredWhy it mattersMethods / references
API gravityDensity relative to water, reported on the API scale at a reference temperature.Supports volume–mass conversion and gives an initial indication of density; it does not determine value alone.ASTM D1298 or D5002; API MPMS Ch. 9
Sulfur contentTotal sulfur, normally reported by mass.Affects corrosion risk, treating demand, catalyst considerations and finished-product sulfur compliance.ASTM D4294; other validated methods may apply
DensityMass per unit volume at a stated temperature.Essential for metering, inventory and custody-transfer calculations.ASTM D1298 or D5002
ViscosityResistance to flow at a stated temperature.Influences pumping, heating, pipeline pressure drop and storage handling.ASTM D445 where its scope fits the sample
Water and sedimentFree or emulsified water and entrained solids, determined by specified procedures.Affects net oil quantity, corrosion, salts, processing and commercial settlement.ASTM D4006 for water; D4007 or D4730 may be relevant
Total Acid NumberAcidic constituents titrated under defined conditions, reported as mg KOH/g.A screening input for crude selection and corrosion management; TAN alone does not predict corrosion.ASTM D664 where applicable
Distillation characteristicsVolume or mass distribution across boiling ranges and fractions.Supports yield estimates, fraction quality assessment and refinery modeling.TBP methods such as ASTM D2892; simulated distillation where appropriate

02EN 590 ultra-low sulfur diesel

EN 590 specifies requirements and test methods for marketed and delivered automotive diesel within its scope. Climate-dependent requirements and national choices matter.

Specification context: EN 590 is a European standard, not a worldwide diesel grade. The current edition, national implementation, climate class, FAME content and contract terms must be checked. ASTM D975 applies in other contexts.

EN 590 ultra-low sulfur diesel technical properties and testing considerations
PropertyWhat is measuredWhy it mattersMethods / references
SulfurTotal sulfur concentration; EN 590 automotive diesel is commonly identified by its 10 mg/kg maximum.Protects emissions-control systems and supports regulatory compliance.EN ISO 20846, EN ISO 20884 or the methods named by the governing edition
Cetane number / indexIgnition quality measured in a test engine or estimated from density and distillation.Relates to ignition delay and combustion behavior; a calculated index is not the same as a measured cetane number.EN ISO 5165; EN ISO 4264 for calculated index
DensityDensity at 15 °C under the applicable method.Supports metering and influences energy delivered per unit volume and engine calibration.EN ISO 3675 or EN ISO 12185
Flash pointLowest temperature at which vapour ignites under the specified closed-cup conditions.A safety and handling property; it is not a complete fire-risk assessment.EN ISO 2719
LubricityWear-scar diameter measured by the high-frequency reciprocating rig.Indicates protection against wear in fuel-injection equipment.EN ISO 12156-1
CFPPCold Filter Plugging Point: the lowest temperature at which the fuel passes a standardized filter under test conditions.A low-temperature operability indicator tied to the applicable climate class, not a guarantee for every vehicle.EN 116
DistillationRecovery at specified temperatures and the boiling-range profile.Relates to volatility, combustion and the consistency of the fuel blend.EN ISO 3405
Fuel cleanlinessWater, particulate contamination and, where required, particle counts.Helps protect filters and high-pressure injection equipment from deposits, wear and blockage.Methods specified by the current EN 590 edition and supply agreement

03Jet A-1 aviation fuel

Jet A-1 is a kerosene-type aviation turbine fuel. Batch certification is only one part of quality assurance through the distribution system.

Specification context: ASTM D1655 defines requirements for Jet A and Jet A-1; DEF STAN 91-091 is also widely referenced for Jet A-1. The purchaser, regulator and distribution system determine the governing requirements.

Jet A-1 aviation fuel technical properties and testing considerations
PropertyWhat is measuredWhy it mattersMethods / references
Freezing pointTemperature at which hydrocarbon crystals disappear on warming under the test procedure.Supports fuel-system operability at low temperatures encountered in aviation.ASTM D5972, D7153 or other methods permitted by the specification
Flash pointClosed-cup flash point under a recognized procedure.A controlled safety classification and handling property.ASTM D56 or D93 where permitted
Thermal oxidation stabilityDeposit formation and pressure-drop response under specified thermal stress.Assesses resistance to degradation in heated aircraft fuel systems.ASTM D3241 (JFTOT)
DensityDensity at a specified reference temperature.Used in quantity accounting and aircraft fuel-system calculations.ASTM D1298 or D4052 where permitted
SulfurTotal sulfur and, where required, specific sulfur species.Relevant to emissions, materials compatibility and specification compliance.Methods listed in ASTM D1655 or DEF STAN 91-091
Water contaminationFree water, dissolved-water response or appearance checks as required.Free water can support microbial growth, freeze and interfere with engine operation.Visual appearance and specified water-response methods; field controls also apply
Particulate contaminationInsoluble particles assessed by filtration, rating or counting procedures.Particles can plug filters and damage tight-tolerance fuel-system components.ASTM D2276 or other specification-listed methods
Specification conformanceA defined batch test programme plus handling and recertification controls.A laboratory certificate alone does not ensure fuel remains uncontaminated through delivery.ASTM D1655, DEF STAN 91-091 and applicable EI/JIG guidance

04Gasoline

Gasoline is a volatile blend of hydrocarbon streams and permitted components. Its requirements vary with market, season and emissions rules.

Specification context: ASTM D4814 is widely used for automotive spark-ignition engine fuel in the United States; EN 228 applies in Europe. Regulations and seasonal schedules may impose additional requirements.

Gasoline technical properties and testing considerations
PropertyWhat is measuredWhy it mattersMethods / references
RONResearch Octane Number measured under comparatively mild engine-test conditions.One measure of resistance to engine knock.ASTM D2699
MONMotor Octane Number measured under more severe engine-test conditions.Complements RON when assessing knock resistance under load.ASTM D2700
Vapour pressureVolatility expressed as vapour pressure under a defined procedure and temperature.Affects evaporative emissions, starting and vapour-lock tendency; seasonal limits vary.ASTM D5191 or specification-permitted alternatives
DistillationThe percentage evaporated across the atmospheric boiling-range test.Relates to starting, warm-up, drivability and deposit formation.ASTM D86
SulfurTotal sulfur in the finished blend.Affects emissions and catalytic after-treatment performance.ASTM D2622, D5453 or other permitted methods
Oxygenates and compositionConcentrations of components such as ethanol, ethers, aromatics, olefins and benzene.Influences volatility, octane, emissions, materials compatibility and legal compliance.ASTM D4815, D5599, D5769 and applicable regulatory methods

05Fuel oil and marine fuels

Residual and distillate fuel oils cover a broad range of products. Grade names alone do not establish quality or compatibility.

Specification context: ISO 8217 specifies marine fuel grades; other residual fuels use market-specific contracts and standards. Statutory sulfur limits depend on the operating area and applicable rules.

Fuel oil and marine fuels technical properties and testing considerations
PropertyWhat is measuredWhy it mattersMethods / references
Kinematic viscosityFlow resistance at a stated temperature.Guides heating, pumping, atomization and injection requirements.ISO 3104 or ASTM D445
DensityDensity at a reference temperature.Used for quantity calculations and can influence separation and handling.ISO 3675, ISO 12185 or ASTM methods as specified
SulfurTotal sulfur by mass.Specification and emissions-area compliance depend on the fuel and operating jurisdiction.ISO 8754, ISO 14596 or permitted alternatives
Flash pointClosed-cup flash point under the specified procedure.A key storage, transport and handling safety property.ISO 2719 or ASTM D93
Water and sedimentWater and total sediment by applicable methods.Affects quantity, combustion, separation, corrosion and stability.ISO 3733 and ISO 10307 series where applicable
Stability and compatibilityPotential for asphaltenic material to precipitate during storage or blending.Incompatible blending can cause sludge, filter blockage and separator problems even when individual fuels meet their specifications.ASTM D4740 or other contract-specified stability tests

06LPG and natural gas

LPG is mainly propane, butanes or mixtures; natural gas is primarily methane with varying amounts of other components. Their tests and custody arrangements differ.

Specification context: LPG may be covered by ASTM D1835, GPA Standard 2140 or EN 589. Natural-gas quality is usually defined by pipeline tariffs, contracts and regulation rather than one universal product specification.

LPG and natural gas technical properties and testing considerations
PropertyWhat is measuredWhy it mattersMethods / references
Hydrocarbon compositionComponent concentrations determined chromatographically.Drives vapour pressure, heating value, combustion behavior and product designation.ASTM D2163 for LPG; ASTM D1945 or GPA methods for natural gas
Vapour pressurePressure exerted by the liquefied gas under a standardized test.Important for storage design, handling and seasonal LPG suitability.ASTM D1267 for LPG
Heating valueEnergy released per unit quantity, often calculated from composition for natural gas.Supports commercial billing and combustion-system operation.Calculated from composition under GPA 2172 / ISO 6976 or the contract method
Sulfur compoundsTotal sulfur and specified reactive sulfur species where required.Affects odor, corrosion, emissions and specification compliance.ASTM D2784 or D6667 for LPG; D5504 or other gas methods where applicable
MoistureWater content or dew point under defined conditions.Helps prevent hydrate formation, corrosion and freezing in gas systems.Chilled-mirror or other validated moisture methods named by the contract
Product purityResidues, non-hydrocarbon gases and other contaminants as applicable.Confirms fitness for the intended storage, transport and end use.Product-specific ASTM, GPA, ISO and contract methods

04 · Standardized testing

Petroleum Laboratory Analysis and Standardized Testing Procedures

ASTM International, ISO, API and Energy Institute methods make measurements more repeatable by defining apparatus, sample preparation, conditions, calculations and reporting. A method number alone is not enough: the edition and product specification determine applicability.

API’s Manual of Petroleum Measurement Standards also connects sampling, metering, temperature and density to quantity determination. Laboratory accreditation to ISO/IEC 17025 covers only the methods and locations within the laboratory’s approved scope.

Laboratory analyst visually inspecting petroleum samples in glass vials

Laboratory testing explorer

Start with the product

EN 590 specifies requirements and test methods for marketed and delivered automotive diesel within its scope. Climate-dependent requirements and national choices matter.

Commonly relevant tests for EN 590 ultra-low sulfur diesel
PropertyTechnical significanceMethods / references
SulfurProtects emissions-control systems and supports regulatory compliance.EN ISO 20846, EN ISO 20884 or the methods named by the governing edition
Cetane number / indexRelates to ignition delay and combustion behavior; a calculated index is not the same as a measured cetane number.EN ISO 5165; EN ISO 4264 for calculated index
DensitySupports metering and influences energy delivered per unit volume and engine calibration.EN ISO 3675 or EN ISO 12185
Flash pointA safety and handling property; it is not a complete fire-risk assessment.EN ISO 2719
LubricityIndicates protection against wear in fuel-injection equipment.EN ISO 12156-1
CFPPA low-temperature operability indicator tied to the applicable climate class, not a guarantee for every vehicle.EN 116
DistillationRelates to volatility, combustion and the consistency of the fuel blend.EN ISO 3405
Fuel cleanlinessHelps protect filters and high-pressure injection equipment from deposits, wear and blockage.Methods specified by the current EN 590 edition and supply agreement

The governing product specification, contract and laboratory scope determine the final test programme, method editions and acceptance criteria.

Showing 11 of 11 methods

Petroleum laboratory testing methods and limitations
MethodPurposeTypical applicationImportant limitation
ASTM D4057Manual sampling of petroleum and petroleum productsProcedures and equipment for obtaining a sample from the sample point into the primary container.Liquid petroleum, crude oils and intermediate products; also addresses associated free water and heavy components.A spot sample represents only its sampling point. Container preparation, mixing and handling remain critical to representativeness.
ASTM D4177Automatic sampling of petroleum and petroleum productsGeneral procedures and equipment for automatic extraction of samples from flowing petroleum streams.Design and operation of automatic sampling systems and primary sample collection.System design, mixing and proving determine whether the sample is representative. Volatility and some products require additional practices.
ASTM D1298Density, relative density or API gravity by hydrometerDetermines density, relative density and API gravity using a hydrometer with temperature corrections.Crude petroleum and liquid petroleum products, especially low-viscosity transparent liquids.Viscous and opaque liquids need suitable equilibrium time and corrections; temperature control is essential.
ASTM D5002Crude-oil density and API gravity by digital density analyzerDetermines density, relative density and API gravity using a digital density analyzer.Crude oils handled as liquids at the specified test temperatures, including some high-vapour-pressure crudes with precautions.Light samples can lose vapour; heavy samples may need temperature control to avoid bubbles and ensure injection.
ASTM D4294Sulfur by energy-dispersive X-ray fluorescenceRapid determination of total sulfur in petroleum and petroleum products.Single-phase liquids, materials liquefiable with moderate heat and materials soluble in hydrocarbon solvents within scope.Matrix differences from calibration materials can affect results; spectral interferences and concentration range must be considered.
ASTM D445Kinematic viscosity of transparent and opaque liquidsMeasures flow time through a calibrated glass capillary viscometer; dynamic viscosity can be calculated using density.Liquid petroleum products exhibiting primarily Newtonian flow behavior.Temperature must be controlled and reported. Non-Newtonian behavior requires careful interpretation or another procedure.
ASTM D664Acid number by potentiometric titrationDetermines acidic constituents under defined titration conditions.Petroleum products, lubricants, biodiesel and blends within the method’s solubility and dissociation scope.Acid number is conditional on the test and cannot by itself predict corrosivity in service.
ASTM D4006Water in crude oil by distillationDetermines water content by distilling the crude sample and measuring recovered water.Crude-oil water determination for refining, purchase, sale or transfer.May be unsuitable where water-soluble alcohols materially affect recovery; homogenization of the test portion is critical.
ASTM D6560Heptane-insoluble asphaltenesDetermines asphaltenes as heptane insolubles under the specified procedure.Topped crude petroleum and residual-containing products such as gas oil, residual fuel, lubricating oil and bitumen within scope.The result is operational, not a complete molecular characterization. Sample topping and additives can affect results.
ASTM D86Atmospheric distillation of petroleum products and liquid fuelsDetermines boiling-range characteristics using a standardized batch distillation.Applicable petroleum products and liquid fuels listed by the method and product specification.It is not a crude TBP assay. Group assignments, condenser temperature and sample properties affect procedure selection.
ASTM D93Flash point by Pensky–Martens closed cupDetermines flash point using manual or automated closed-cup procedures.Petroleum products and other materials within the applicable temperature range and procedure.A controlled laboratory response, not a complete assessment of real-world fire hazard. The correct procedure matters.

Scopes summarized from ASTM’s published descriptions and checked on 17 November 2026. ASTM revisions change; use the current licensed standard for laboratory or contractual work.

05 · Verification

Quality assurance and product verification

Quality assurance is a chain of decisions, not a single certificate. It starts with a representative sample and ends only after results, documents and operational evidence have been reviewed by responsible people.

Quantity verification asks how much product is present, using measurements such as level, flow, temperature and density. Quality verification asks whether the material’s measured properties meet stated requirements. Neither, by itself, establishes ownership, title, allocation or physical availability.

  1. 1

    Product sampling

    Use a sampling point, method and frequency suited to the parcel and product. A non-representative sample cannot be repaired by precise laboratory work.

  2. 2

    Sample identification

    Seal, label and record the sample, source, time, conditions and custody transfers so results remain traceable to the material sampled.

  3. 3

    Laboratory analysis

    Use competent personnel, suitable methods, calibrated equipment and quality-control checks. ISO/IEC 17025 accreditation applies only to the scope actually covered.

  4. 4

    Specification comparison

    Compare results with the governing product standard, contract, regulation and measurement-uncertainty or decision-rule requirements.

  5. 5

    Quality documentation

    A Certificate of Analysis reports tested properties. Quantity and quality inspection reports answer different questions and should identify the sampled parcel and methods.

  6. 6

    Operational review

    Responsible personnel review discrepancies, investigate contamination, quarantine off-specification material where required and decide disposition under the contract.

When a result is outside specification

The material may be segregated while the result is checked. Investigation considers sampling, contamination, laboratory quality control and the applicable decision rule. Retesting should follow the governing procedure—not simply continue until a passing result appears.

Through storage and transport

Tank histories, line displacement, shared manifolds, water bottoms, cleaning records and receipt checks help preserve quality. Independent inspectors can witness or perform defined activities, but their report remains bounded by its stated scope.

06 · Refinery processing

From crude oil to qualified products

Refineries combine separation, conversion and treatment. Distillation sorts molecules mainly by boiling range; conversion changes molecular structures; treatment removes unwanted components or stabilizes streams. Blending then brings qualified components together.

Select each unit to follow the material through the core sequence. Streams recycle, bypass or move between units according to refinery design and operating objectives.

Preparation

Reception & desalting

Crude oil → desalted crude

Incoming crude is received, mixed and commonly washed to remove water, salts and solids before heating. Effective desalting helps limit corrosion, fouling and catalyst contamination downstream.

Refineries combine these units in different configurations. Residues may also feed coking, deasphalting, gasification or other processes beyond this core sequence.

07 · Field fundamentals

Before analysis: where production begins

What Is Crude Oil?

Crude oil is a naturally occurring mixture of hydrocarbons formed from ancient organic material and trapped in porous rock underground.

How Oil Wells Produce Crude Oil

A well connects the reservoir to the surface. Reservoir pressure, often supplemented by artificial lift such as a pumpjack, moves fluids up the wellbore.

Producing Wells and Decline Rates

Production falls over time as reservoir pressure declines. Decline rates shape a well's reserves and economic life.

Upstream, Midstream and Downstream

Upstream covers exploration and production. Midstream covers gathering, transportation and storage. Downstream covers refining and fuel distribution. Rock Creek Oil's focus is upstream production; it is not a refinery, terminal, fuel distributor or trader.

Questions about analysis verification can be sent to analysis@rockcreekoil.com.